Ra ek: Excellent video but please tell us which is the most reliable washing
machine? Panasonic, Miele or LG? I use mine every day (4 kids) and I have
already have enough experience to know that Bosch, Siemens & the Zanussi
clan dont last much more than 4 years before becoming uneconomical to
repair using a trade.
skoob6969: DUDE,,,, I have those shoes... totally comfortable
Jason Martin: Thank you for a very well done video. My LG has a different problem, but I
found your info to be helpful in getting in to the machine, and for getting
into diagnostics. My machine will not stop filling, even when off or
unplugged from the wall. Checking the inlet filters, they were very dirty
(covered in scale), so my guess is that mineral deposits have blocked the
valve from closing. I have tried to find a video that covers this, to no
avail. Any suggestions other than toss the machine over the balcony and buy
an old school top load Kenmore?? Thanks.
Donna Dixon: Thank you! My husband followed your instructions to diagnose our washer's
problems and reinstall the control board.
kevin romo: Hello Zack, my question is what do I do if the washer doesn't power on at
all? Yes its plugged in to LOL
hubertmiranda: Hi Zack. We have an LG front loading machine (WM1832CW). It spins but stops
before you get to the spin/drain cycle and an LE error code appears. Any
ideas on how to fix this issue? Is it the strator? control panel? motor?
Shannon Lastowski: Zack, thanks so much! Boy, do I wish you made house calls in my area. I
just washed a heavy jute rug, now it won't drain the water out. I'm going
to try the diagnostic, as a repair person cant come for over a week. THANKS
for this great video!
anita westbrook: my machine goes through cycles and then stops when it is time to drain and
gives an error message of 0E. what can I do
Zack Nelson: Yes you could check continuity but your not ensuring your windings are ok
when you do that. The only way to be sure your motor is ok is to get the
proper resistance between the windings.
cityboynthestxs: I also replaced the motor sensor. Still doesn't work.
Zack Nelson: I think the IU 02 is your software version and not sure what IN 80 is but
it sounds to me like your control board is the problem! Do you get any
error codes after you put it into the cycle? and does it just stop after
water needs to drain?
Remi Savard: Also is it possible that it could be the rotor position sensor?
bbsadlerb3: good video! Time to see why my washer wont spin I cant even spin the drum
by hand anymore.
Robert Brinton: excellent video. Mine has no issues except an odor issue. while i was
researching info on mine, found your vid. if I ever have this issue, I will
know how to replace the control board. great job dude! Robert
ideakeyk1: I got an error code of LE. Thanks.
Remi Savard: Hey what if i receive to much voltage? 230 volts is what im getting! thanks
for your answer! great video btw!
TheTruth7242: I Liked Your Video...THANKYOU. 8D
Zack Nelson: I would say so! People have their own opinions though!
EurekaRecycler: I think LG is more customer friendly for DIYer's
Zack Nelson: You need to know the correct frequencies. I do not have that information
cityboynthestxs: Hey Zack thanks for the help. yes I did the test mode. The door does lock
automatically on first button push. I also tried pulling the door open.
press 2nd time and no spinning inside at all. It will spin both ways very
easily by hand. I did check the motor connector even the other end to make
sure I was doing the right one. Followed steps just like your video. I do
know how to use the meter too. Would I be able to continuity on the
windings does it work same way?
TheTruth7242: Actualy..Yes it did :) THANKYOU...Zack Nelson 8)
cityboynthestxs: as i am checking the windings at the plug I am not getting 7 or 8 ohms I
get zero. Does that mean my motor is bad. I also do not get any voltage at
this same plug. Must be a bad board. I followed all the steps in your
video. Drum will not spin on test mode. Zero rpms. Any ideas?
ideakeyk1: Great video! What else should I check if the drum only spin one direction?
sangie777: My washer does not drain or goes into the spinning cycle, I tried the
diagnostics mode and it says IU 02 and In 80... if I press start button
again while in diagnostics mode it drains the water and spins very fast...
Can you please tell me what could be causing this problem? I would really
appreciate it. Thanks in advance!
Zack Nelson: Thank you! I hope it helped you out!
Bob smith: NONSENSE -Crazy, I have same washer and when it did not spin the water out
I just restarted for wash cycle
Zack Nelson: Putty knife.
Zack Nelson: Thanks Robert I really appreciate it!!
Zack Nelson: Thank you!!
EurekaRecycler: How do you test the Pressure Switch? Thanks
Richard Holloway: LG better than Hotpoint?
Richard Medina: Where can I purchase a new board and roughly what do they cost?
Zack Nelson: Make sure your checking the plug that goes directly into the motor and if
you get the same resistance between all three windings then I would suspect
your door switch or your control board. Door switch has to be closed to
send voltage to motor.
EurekaRecycler: Thanks, do U know how to check the water level /pressure switch?
Richard Medina: When I press the bottoms like you said I should do the number displayed is
41 and at times moves to 42... can you tell me what thus means?
Zack Nelson: So LE typically means that the hall effect sensor has failed. Did you run
the machine on diagnostics mode and which way is it not turning?
Nathan Dickamore: Just saved me a repair call. Thanks Zach!
pooters1966: Great video! Thanks!
OnRock19: 4:03 with what knife?
How to Fix an LG Front load washer machine that wont spin4.5
out of 5